Skip to content
Technical & commercial enquiries: sales@rssechem.com Certificate of analysis issued per lot · Worldwide shipping
Register Request a quote & Contact us

How much evidence identifies an unknown impurity: from a formula to a structure

Impurities & regulation Published By RSSE Technical Team · Reviewed by RSSE Quality Unit

A formula is not a structure, and a library match is not an identification. This works through what each layer of evidence actually proves - the formula search, the isotope arithmetic, the fragment that cannot fix a position - and the one step that converts a proposed structure into an identified impurity.

On this page

An identified impurity has a definition, and it is not a library hit

ICH Q3A defines an identified impurity as an impurity for which a structural characterisation has been achieved. The definition is short and it sets the bar. A peak that matches a spectrum in a library, or an accurate mass that fits one elemental composition, is not structural characterisation. The guideline asks for the studies conducted to characterise the structure of impurities above the identification threshold to be described, which means the reasoning has to survive being read by someone who was not in the laboratory.

That distinction carries commercial weight. Everything downstream of identification - the qualification argument, the specification limit, the impurity standard that makes the method quantitative - rests on the structure being right. An isomer assigned in error produces a limit for a compound that is not in the batch, and no amount of later method work repairs it.

The formula narrows the search, it does not end it

Accurate mass is the cheapest evidence available and the most over-read. Take an ion at m/z 455.2111 in positive mode and search carbon, hydrogen, nitrogen, oxygen and sulfur within 40, 70, 8, 14 and 2 atoms, keeping only compositions with an integer ring-and-double-bond equivalent between 0 and 30. At 5 ppm, seven compositions survive. At 2 ppm, three. At 1 ppm, one: C24H30N4O3S, at twelve ring-and-double-bond equivalents.

That looks like an answer and is not one. Twelve degrees of unsaturation in a molecule carrying four nitrogens, three oxygens and a sulfur is compatible with a very large number of connectivities, and every one of them returns the same exact mass and the same isotope pattern. Mass measures composition; identification is a claim about connectivity. The distance between the two is where most of the analytical work sits.

Two cautions on the search itself. The list is only as good as its constraints: widen the sulfur range or allow phosphorus and the 1 ppm window reopens. And 1 ppm is an instrument specification measured on a calibrant, not a promise for a peak sitting at 0.05 per cent of full scale in a dirty matrix, where the mass error is routinely two to three times the error on the tuning solution.

The isotope pattern is a subtraction, not a threshold

The textbook rule is that one sulfur appears as an M+2 of about 4.4 per cent. Used as a threshold the rule misleads, because carbon contributes to M+2 as well.

For C24H30N4O3S the calculated M+1 is 28.7 per cent of the monoisotopic peak and M+2 is 9.1 per cent. Part of that M+1 is not carbon at all: twenty-four carbons give 25.7 points, four nitrogens 1.5 and the sulfur 0.75, leaving under a point to the hydrogens and the 17O. Dividing 28.7 by 1.1 returns 26 carbons, two too many, so the carbon count cannot be read until nitrogen and sulfur have been assigned.

M+2 behaves the same way. Keep twenty-four carbons, drop the sulfur and take the oxygens from three to five: M+2 falls from 9.1 to 4.8 per cent. The 4.3-point difference is the sulfur; the 3.2 points that remain are the 13C pair among twenty-four carbons. At this size the sulfur is still visible, but it is a minority of M+2, and a rule expecting 4.4 per cent and finding 9 would have reported no sulfur at all.

The pattern earns its place for another reason: it is orthogonal to mass accuracy. Sulfur and two oxygens differ by 17.8 mDa, which is 39 ppm at m/z 455. An instrument that cannot resolve those two compositions can still separate them on isotopes, because the sulfur version carries 4.25 per cent of 34S where the oxygen version carries 0.4 per cent of 18O.

Fragments prove a substructure, never a position

Product-ion spectra are where a formula becomes a hypothesis, and where the hypothesis is most often over-claimed. A neutral loss of 28 Da is reported as carbon monoxide or as ethylene depending on what the analyst expected. The two differ by 36 mDa - 27.9949 against 28.0313 - which is 85 ppm on a fragment at m/z 427 and needs a resolving power near 12000 to separate. A nominal-mass instrument returns the same 28 for both, and the assignment is then an assumption wearing the clothes of a measurement.

Even a correctly measured loss proves less than it appears to. A loss of 43.9898 is carbon dioxide and a loss of 44.0262 is C2H4O, and either can arise from more than one position on the same skeleton. What a fragment establishes is that a set of atoms left the ion as a unit, not where they were attached. Positional isomers fragment into the same pieces, which is why a fragmentation tree narrows a structure without ever closing it.

Intensity adds a further caution. Fragment ratios move with collision energy, cone voltage, source temperature and matrix load, so a library match on an MS/MS spectrum compares spectra, not structures. Two laboratories running the same compound on different instruments can return scores that differ by more than the gap between two candidates.

Retention is evidence only when the mechanism changes

Relative retention on the method that found the peak is a consistency check, not an identification. Two isomers separated by 0.3 minutes on one C18 gradient can invert on another, so agreement on a single method excludes very little.

What discriminates is a second mechanism: a different stationary phase, a different mobile-phase pH, or a mixed-mode column, chosen because the candidate isomers are predicted to move relative to each other. If the unknown and the candidate standard co-elute on both, the case is far stronger than two runs on the same method. If they split on the second, the structure is wrong and the finding cost one injection.

The corollary matters when buying: a certificate that reports a retention time and a purity without stating the method cannot support an identification claim, because the retention number does not transfer to any other system.

What a reference standard adds that no spectrum does

A standard does two things a spectrum cannot. It fixes the retention time, which turns a proposed structure into a specific peak in a specific method, and it supplies a response factor, which is what converts a peak area into a percentage.

ICH Q3A is explicit about the second. Impurity levels can be estimated against the response of the drug substance itself, and where the response factors of the substance and the impurity are not close, the practice remains appropriate provided a correction factor is applied or the impurities are being overestimated. Read plainly, a laboratory without the impurity standard has two honest options: apply a measured relative response factor, or declare that the reported figure is an upper bound. A figure published with neither is a number with no stated basis.

The same guideline asks that reference standards used to control impurities be evaluated and characterised according to their intended use. For an identification standard that means the certificate should state how the structure was established, not only what the purity is.

Four claims, and the evidence each one needs

ClaimEvidence heldWhat can be writtenWhat is still missing
Peak detectedRetention on one method, UV spectrumAn unknown at a stated relative retention and area per centEverything above it
Composition assignedAccurate mass inside 1 ppm, isotope fitA formula, with the search space statedConnectivity
Structure proposedFormula, product ions assigned, a route consistent with forced degradationA proposed structure, described as tentativeAn independent confirmation
Structure confirmedCandidate standard co-injected, ions and retention matching on two mechanisms, or NMR connectivityAn identified impurity, in the sense the guideline usesNothing for identity; the response factor for quantitation

The table reads downward as a cost table too. Each row costs more than the one above it, and each supports a claim the row above cannot. A submission reporting a structure at the third row is not wrong; it is reporting a hypothesis, and the strongest version of that submission says so in those words.

Where NMR settles what mass spectrometry cannot

Nuclear magnetic resonance is the only routine technique that reports connectivity directly: which proton sits on which carbon, and through two or three bonds, which fragments are joined. For positional isomers that share a formula and a fragmentation pattern it is usually the only in-house answer.

The constraint is amount. An impurity at 0.10 per cent in a one-gram batch is one milligram, enough for a proton spectrum on a modern instrument and marginal for the two-dimensional experiments that establish connectivity. That arithmetic, not the cost of instrument time, decides whether an unknown earns a confirmed structure or a proposed one, and it is worth doing before the isolation campaign is planned rather than after it has been paid for.

Buying a standard before the structure exists

Impurity work carries a sequence problem: the standard cannot be ordered until the structure is known, and the structure is usually confirmed with a standard. The way out is not to buy early but to buy deliberately, and the questions that decide the purchase are the ones a catalogue entry does not answer.

Ask whether the lot is the isomer proposed rather than a mixture, since positional and stereo isomers share a formula and often a mass spectrum. Ask how the structure of that lot was established, and whether the evidence sits on the certificate or only in a technical pack. Ask what the assigned content is expressed against - as is, dried, or free base - and what the uncertainty is at the stated coverage factor. A certificate that answers none of these supports a purity figure and nothing else.

What to keep in the file

The record that survives review is the reasoning rather than the spectra: the search space and the mass error, the isotope fit with the arithmetic shown, the fragments assigned and the ones left unexplained, the second mechanism used for retention, and the standard lot with the sentence from its certificate that states how the structure was established. An unexplained fragment is not a failure to hide. It is the honest edge of the claim.

The guides below cover the threshold that triggers the obligation, the standard that closes it, and the stress work that generates the peaks in the first place.

what an impurity reference standard is | the three impurity thresholds | forced degradation study design | impurity profile comparison | chiral and stereoisomeric standards | reading a certificate of analysis

Frequently asked

Is an accurate mass inside 1 ppm enough to identify an impurity?
No. It assigns an elemental composition, and a composition is compatible with many connectivities. On the worked ion at m/z 455.2111 a search over carbon, hydrogen, nitrogen, oxygen and sulfur leaves one composition at 1 ppm, C24H30N4O3S with twelve ring-and-double-bond equivalents, and that formula still fits a very large number of structures that share the same exact mass and isotope pattern.
Can an impurity be called identified on a library match alone?
Not in the sense the guideline uses. An identified impurity is one for which structural characterisation has been achieved, and a spectral similarity score compares spectra rather than structures. Fragment ratios also move with collision energy, cone voltage and matrix load, so a match score is not transferable between instruments.
We do not have the impurity standard. Can we still report a percentage?
Yes, with a stated basis. Impurity levels can be estimated against the response of the drug substance where a correction factor is applied, or reported as an upper bound where the impurity response is not close to the substance response. A figure published without either is a number with no stated basis.
Two isomers give the same accurate mass and the same fragments. How are they separated?
Three ways, in rising cost. A second chromatographic mechanism chosen because the candidates are predicted to move relative to each other; co-injection with the specific isomer standard, which fixes retention and excludes the alternative; or NMR, which reports connectivity directly and is usually the only in-house answer for positional isomers.
How much material does a confirmed structure need?
The arithmetic is worth doing before the isolation is planned. An impurity at 0.10 per cent in a one-gram batch is one milligram, which is enough for a proton spectrum on a modern instrument and marginal for the two-dimensional experiments that establish connectivity.
A supplier certificate states a retention time and a purity. Does that prove identity?
No. A retention time without the method does not transfer to any other system, and a purity figure says nothing about how the structure was established. The certificate should state the method and how the structure of that lot was confirmed, not only the two numbers.

Sources and further reading

Every document below is published by the body that owns it; none of them is a summary written by us. Accessed 2026-11-20.

Send us a CAS number

Availability, documentation and lead time — answered by the people who handle the batch, not a ticket queue.

Request a quote sales@rssechem.com

How to read a certificate of analysis Field by field: identity, purity, content basis, the retest date, and the questions worth asking a supplier before you file the document.How to choose a reference standard supplier A practical checklist for evaluating reference standard suppliers on documentation, traceability, lot consistency, logistics and technical support.Stable isotope-labelled standards and when to use them When labelled internal standards earn their place in an LC-MS or GC-MS method, what to specify when ordering, and the traps in quantitative work.Nitrosamine and NDSRI standards: what to test for and what to buy The difference between small nitrosamines and NDSRIs, what a laboratory needs as a standard for each, and how to specify one so the result stands up to review.What is an impurity reference standard? What the term means, how it differs from a pharmacopoeial standard and a working standard, what the documentation has to state, and how to pick the right form and purity basis.ICH M7 in practice: classifying mutagenic impurities How the five-class hazard assessment works, what the 1.5 microgram default really covers, and how the four control options decide which standards you buy.qNMR vs mass balance: how purity is really assigned Two certificates, one compound, two purity values. What mass balance and qNMR each measure, why the figures differ, and how the basis changes the number.Elemental impurities: from a PDE to a limit you can measure How a permitted daily exposure becomes a concentration limit, why the dose moves the number, and what an elemental impurity specification must state.Salt, hydrate and free base: converting content so the numbers reconcile How to move content and impurity values between as-is, anhydrous and free-base bases, in what order, and why the basis can turn a pass into a fail.Forced degradation study design: how far to push each stressor How to set stressor strength, read a kinetics screen, judge mass balance and catch over-degradation before it wastes a method development cycle.Analytical method transfer: acceptance criteria you can defend Four transfer routes, criteria built from the method's own precision, and the standard's assigned content that shifts every result by a fixed amount.Chiral and stereoisomeric impurity standards Enantiomer, diastereomer, epimer, E/Z isomer: four different standards and four different questions. What each has to state before it can control a method.Reference standard, analytical standard, CRM: what the words mean Four labels appear on the same vial in different catalogues. They are not synonyms, and the difference decides what you may claim in a report.Peptide reference standards: what changes when the analyte is a chain Deletion sequences, epimers, pyroglutamate, deamidation, counter-ion and water: why a peptide standard needs a different certificate from a small molecule.Cleaning validation residue limits: where the number comes from How a residue limit is derived from the dose, from 10 ppm and from a health-based PDE, and what the swab method and its standard must be able to reach.Cold chain and stability of reference standards: what transport and receipt checks protect Storage regimes, stability budgets and mean kinetic temperature, plus the receipt checks that decide whether a standard still supports its certificate.Impurity profile comparison: what a reference standard proves, and what it does not How reporting, identification and qualification thresholds set the scope of an impurity profile comparison, and where a standard stops proving anything.Weighing a reference standard: minimum weight and moisture How the 0.10% repeatability rule sets a minimum weight, why a hygroscopic standard is used as is, and which figures belong on the worksheet.Standard solution stability: how long a prepared standard can be used How to set a hold time for a standard solution: two baselines, six failure modes, a defensible study design and criteria fixed before the data arrive.Reporting, identification and qualification thresholds by dose How the 0.05, 0.10 and 0.15 per cent thresholds are banded by dose, where the milligram cap takes over, and what each limit forces you to test.USP 233 in practice: the J value and the four preparation routes How chapter 233 turns a limit into a J value, which of four preparation routes to use, and the acceptance criteria a method must meet before routine use.Building an uncertainty budget for a standard solution A worked budget for a 1 mg/mL standard solution: weighing, assigned value and volume, the correlation trap, and when k = 2 understates coverage.When the reference standard is the suspect in an OOS result How to test whether a reference standard caused an out-of-specification result, and how to separate a changed material from a misapplied assigned value.Two certificates for one compound: reconciling them field by field How to compare two certificates for the same compound: identity, measurand, basis, assignment, uncertainty, and the order that makes the numbers comparable.